STANDARD FLOOR LOOMS
click here for MANUAL | click here for DIMENSIONS
click here for MAINTENANCE INSTRUCTIONS & WARRANTY | click here for LABELED IMAGE
36" Low Castle Maple Standard Floor Loom
ACCESSORIES & FEATURES
Our Standard floor loom comes in two styles: The Standard Low Castle and The Standard High Castle. Though both looms take up identical floor space, the lower profile of the Low Castle model appears visually smaller. A High Castle loom includes a storage tray and holes drilled in the top of the castle uprights for the swivel pin of an extension lamp, otherwise the looms function the same. Both the Standard Low Castle and the Standard High Castle looms are available in 36" and 46" wide weaving widths.
All Standard floor looms may be ordered with eight or Four Now-Four Later* shaft options. The number of shafts you choose will depend on the kind of weaving you intend to do. Though most weave structures can be woven on four shafts, additional shafts increase your pattern options extensively. If you have a keen interest in pattern drafting and weave structures, eight shafts will allow you to fully develop this interest.
The Schacht Standard floor loom has an under-slung jack mechanism to raise the shafts. The jacks pivot from two points equidistant from the center and lift the shafts by pushing up on the center point. We employ a parallel lamm system which gives our looms a light treadling action. Because of this parallel lamm, it isn't necessary to adjust the tie-up cords.
Our tie-up system is quick and easy to use. Pre-measured nylon tie-up cords hang from the lamms and are attached to a treadle by sliding the appropriate cords into the treadle slot. This makes changing tie-ups very fast.
Other special features of our Standard floor looms include: friction reducing aluminum shaft channels, a back beam which folds with or without a warp on the loom, removable back and breast beams, and an adjustable open-sided beater. Our braking system employs a ratchet and dog on the cloth beam and a friction brake on the warp beam. This combination give you precise tension control at all times.
*"Four Now - Four Later" (4N4L) is an eight harness loom shipped with only four harnesses installed, but with the capacity to add an additional four harnesses. You can purchase a kit to add four harnesses at a later time. 4N4L looms are shipped with all the heddles, tie-ups and other items normally included with an eight harness loom.
Sectional BeamOur sectional beams are easily assembled and can be installed on the existing warp beam of your Schacht loom at any time. Sectional beams for Standard floor looms have 2" sections and a one half yard circumference. They are available in maple or cherry with maple pegs. |
|
RaddlesRaddles help keep a warp spread evenly as it is wound onto the warp beam. Ours have built-in clamps and can be attached to either the loom's back beam or the shuttle race of the beater. Raddles come with plated pins inserted every inch and with holes drilled every half inch with enough extra pins included should you prefer half-inch spacing. |
|
Double Back BeamsTo facilitate different warp tensions for weave structures such as warp pile, supplementary warp, and Bedford cord. A double back beam is a healpful accessory to add to your loom Installation is straight-forward; holes have been predrilled in the loom for easy assembly. Double beams come with a separate brake. |
 |
Standard Floor Loom with lamp holderThe Standard Low Castle with lamp holder, shown on low castle loom. The high castle loom has a hole for the lamp in the castle side. |
 |
Loom Bench with bench bags |
 |
Dimensions
Weaving Width |
36" |
46" |
| Overall Width |
44" |
53" |
| Height at Breast Beam |
32" |
32" |
| Height-Low Castle |
37" |
37" |
| Height-High Castle |
46" |
46" |
| Depth-Open |
38" |
38" |
| Depth-Folded |
26" |
26" |
| Weight-8-Shaft |
125 lb |
141 lb |
| Weight-4 Now-4 Later |
110 lb |
125 lb |
| Weight-High Castle |
add 10 lb |
|
| Weight-Shipping |
add 27 lb |
|
| Weight-4 Later Kit |
15 lb |
16 lb |
| Heddles-8 Shaft |
1000 |
1000 |
| Heddles 4 Now-4 Later |
1000 |
1000 |
STANDARD FLOOR LOOM ACCESSORIES |
||
| 36" Double Back Beam |
|
19 lb |
| 46" Double Back Beam |
|
22 lb |
| 36" Sectional Beam |
9" x 3" x 2" |
7 lb |
| 46" Sectional Beam |
8" x 3" x 2" |
9 lb |
| Raddle for up to 26" |
29 1/2" x 3" x 1" |
1 1/2 lb |
| Raddle for up to 40" |
44 1/2" x 3" x 1 1/2" |
2 1/2 lb |
| Raddle for up to 48" |
52 1/2" x 3" x 1 1/2" |
3 lb |
| Lamp Holder |
4 1/2" x 2 1/2" x 1 1/4" |
8 oz |
REEDS AND HEDDLES |
||
| 36" & 46" Reeds |
Total Length: 1" longer than weaving width |
|
| Flat Steel Heddle |
9" from center of eye to center of eye-9/16" eye |
|
| Inserted Eye Heddle |
9" from center of eye to center of eye-1/4" eye |
|
| Texsolv String Heddle |
9 3/8" end to end-1/2" eye |
|
**Suggested Retail Prices and Specifications Subject to change without notice**
click here for MANUAL | click here for DIMENSIONS
click here for MAINTENANCE INSTRUCTIONS & WARRANTY | click here for LABELED IMAGE